Accessories

Arduino Acessories
Sort By:  
CP2104
CP2104 USB to UART with RTS
CAD$3.49
CP2102 USB to UART Converter
CAD$3.49
Various USB Cables
CAD$0.99
ESP-01 adapter
ESP-01 Bread Board Adapter
Out of Stock
CAD$0.39
FTDI USB to UART Converter with Break Out
Out of Stock
CAD$5.89
STK500 USBASP
CAD$4.99
FTDI USB to UART Converter
CAD$3.89
BreakOut module for ESP-01 ESP-01S
CAD$2.49
BreakOut module for ESP-07 ESP-08 ESP-12E/F
Out of Stock
CAD$1.29
USBasp adapter
USBasp Bread Board Adapter
CAD$0.29
I/O Breakout for Nano / Nano32 / Nano168
CAD$3.49
Powered Terminal Block for Nano
CAD$4.49
2 pc Heat Sink Kit - RaspBerry
CAD$3.49
External IPx WiFi Antenna for ESP boards
CAD$0.99
ESP-01 Programmer
CAD$2.99
LGT8F328P and AVR multi ISP Programmer
CAD$4.99
CP2104
CP2104 (CP2104)
USB UART with both DTR and RTS for BreadBoarding ESPs. Jumper selectable 3V3 or +5V Supports RESET via DTR for regular AVR MPUs or, Reset via RTS for ESP MPUs. the selection is done automatically by the Arduino IDE. allows for automatic programming without having to hit the "Flash" button or moving jumper wires... Note this is a rev. 0.9 proto board so it is not pretty and the LEDs on the RxD/TxD do not light - they are on GPIOs of the 2104 so this may be a software issue. The female header is designed to connect a USB breakout board so you can choose the type of USB connector.... see "Related Products" tab to the right.
CP2104 USB to UART with RTS
CAD$3.49
CP2102 (CP2102)
  • Connect to your Pi or Arduino Serial Port via USB
  • Supports RESET via DTR


CP2102 USB to UART Converter
CAD$3.49
USB Cables (USBcable)
various cables...

"micro" is typically used for the Nano32 - 1m long

"mini" is typical for the "normal" Nano - 1m long

the "A" extension is good for the USBasp - 1m long

NOTE - the micro with switch is POWER-ONLY - no data - NOT for Uploading..  2m long
           - Colours may vary from photo.
Various USB Cables
CAD$0.99
ESP-01 adapter
ESP-01 adapter (8Sprdr)
ESP-01 Bread Board Adapter
ESP-01 Bread Board Adapter
Out of Stock
CAD$0.39
FTDI Break Out USB to UART (FTDI-BO)
  • Connect to your Pi or Arduino Serial Port via USB


FTDI USB to UART Converter with Break Out
Out of Stock
CAD$5.89
Arduino ASP (USBasp)
The ISP gives you the freedom to program all of the flash memory including the bootloader, you might want to use caution!!

  • ATmega8 Chip - Tested on Win10 and Ubuntu
  • 3.3V and 5V switch selectable.
  • USB- connector
  • 50cm 10 pin Ribbon cable


Firmware upgrade eliminate the "unable to set sclk" error/warning

includes TPi protocol for programming ATtiny10 family of MCUs



STK500 USBASP
CAD$4.99
FTDI USB to UART (FTDI)
  • Connect to your Pi or Arduino Serial Port via USB
  • Connect the 3 female jumper connectors to your development board's RX, TX and GND pins
  • Then use Putty to communicate with the corresponding COM port such as /dev/ttyUSB0


FTDI USB to UART Converter
CAD$3.89
ESP-01 BreakOut (ESP01-BO)
BreakOut module for ESP-01 or ESP-01S Male pins unsoldered includd
BreakOut module for ESP-01 ESP-01S
CAD$2.49
ESP-07/08/12 BreakOut (ESP07-BO)
BreakOut module for ESP-07 ESP-08 ESP-12E/F Male pins unsoldered includd
BreakOut module for ESP-07 ESP-08 ESP-12E/F
Out of Stock
CAD$1.29
USBasp adapter
USBasp adapter (10Sprdr)
USBasp Bread Board Adapter
USBasp Bread Board Adapter
CAD$0.29
Nano Expansion - Unassembled (NanoEXP)
Requires Soldering
I/O Breakout for Nano / Nano32 / Nano168
CAD$3.49
Nano Powered Terminals (NanoTerm)
Powered Terminal Block for Nano / Nano32 / Nano168
Powered Terminal Block for Nano
CAD$4.49
Heat Sink Kit (HSink3)
2 pc Heat Sink Kit for RaspBerry Pi or Orange Pi or ESP8266/ ESP32 / Motor Controller Aluminium with peel off mounting tape.
2 pc Heat Sink Kit - RaspBerry
CAD$3.49
External IPx WiFi Antenna (AntIPx)
External IPx WiFi Antenna for ESP boards.

15cm length
External IPx WiFi Antenna for ESP boards
CAD$0.99
ESP-01 Programmer (ESPprg)
ESP-01 Programmer:

This is our own design...

Designed to operate with an FTDI or CP2102 USB to Serial convertor.
Female Headers are provided.

On-Board Switch selects programming mode..

This board also serves as a breakout to allow use of the ESP-01 on a breadboard..
... and may also be used to adapt a CP2102 or FTDI to a proMINI32.
ESP-01 Programmer
CAD$2.99
multiASP (LGTasp)
The LGT8F328P Processor cannot be programmed via the SPI bus like the Atmel chips. An USBasp will not work. The Logic Green chips are programmed using a SWD programmer.

We have developed our own due to a lack of such a product on the open market.  Basically it is a proMINI32 with a shield to which you can connect another proMINI32 or Nano32.  You can upload programs via the Arduino IDE just like an USBasp.  It is compatible with David Buezas' excellent LGT8F boards package.  There are also provisions to use it with Atmel boards like the Nano, proMini and even an Uno or Mega. There are on-board LEDs which give an indication of programming progress and which board has been detected..

Using an ASP/ISP gives the benefit of saving the flash memory used by the bootloader.  You also get instant-ON because there is no bootloader. It is also need to install a bootloader should it be missing or damaged.  For example, I find that freeRTOS will not run on the LGT board with the bootloader installed (it stomps on the WDT vector), but using the ISP removes this problem and gives me another 1/2K of flash which comes in handy.  By definition a typical freeRTOS project needs more memory.

It is designed with a socket for a CP2102 UART board, but you could connect a FTDI using jumpers.

The rev 0 board had a design layout error and so has 1 jumper wire installed..  This was corrected in rev 1.

A brief operating guide (and better photos) is available on my github


LGT8F328P and AVR multi ISP Programmer
CAD$4.99
Per Page      1 - 16 of 16
  • 1